Electronics

Bipolar Junction Transistors (BJT)

By placing two PN junctions together we can create a bipolar junction transistor. In a PNP transistor the majority charger carriers are holes and typically germanium is favored for these devices. In NPN transistors the majority charger carriers are electrons; for this case, silicon is typically used.

PNP schematic symbol and (b) physical layout
Figure 1:  (a) PNP schematic symbol and (b) physical layout

Figure 2: (a) NPN schematic symbol and (b) physical layout

The thin and lightly doped central region is known as the base (B) and has the majority charge carriers of opposite polarity to those in the surrounding material. The two outer regions are known as the emitter an (E) and the collector (C). Under the proper operating conditions the emitter will emit or inject majority charge carriers into the base region, and because the base is very thin, most will ultimately reach the collector. The emitter is highly doped to reduce resistance. The collector is lightly doped to reduce the junction capacitance of the collector-base junction. The emitter-base junction is forward biased while the collector-base junction is reversed biased. The resistance emitter-base junction is very small as compared to collector-base junction. Therefore, the forward bias applied to the emitter-base junction is generally small whereas reverse bias on the collector-base junction is much higher.

Related: The Basics of Semiconductor Physics as the Foundation of Electronics

The Transistor Operation (NPN)

The figure below shows the NPN transistor with forward bias to emitter-base junction and reverse bias to collector-base junction.

Figure 3: Basic connection of NPN transistor

The forward bias causes the electrons in the n-type emitter to flow towards the base. This constitutes the emitter current IE. As these electrons flow through the p-type base, they tend to combine with the holes. As the base is lightly doped and very thin, therefore, only a few electrons (less than 5%) combine with the holes to constitute base current IB. In other words, the electrons which combine with holes become valence electrons. Then as valence electrons, they flow down through holes and into the external base lead. This constitutes base current IB. The remainder (i.e. more than 95%) cross over into the collector region to constitute collector current IC. In this way, almost the entire emitter current flows in the collector circuit. Hence the emitter current is the sum of collector and base currents:

IE = IB + IC

Most of the electrons from emitter continue their journey through the base to collector to form collector current because:

  • The base is lightly doped and very thin; therefore, there are few holes which find enough time combine with electrons.
  • The reverse bias on collector is quite high and exerts attractive forces on these electrons.

Transistor Operation (PNP)

The figure below shows the basic connection of a PNP transistor.

Figure 4: Basic connection of PNP transistor

The forward bias causes the holes in the p-type emitter to flow towards the base. This constitutes the emitter current IE.

As these holes cross into the n-type base, they tend to combine with the electrons. As the base is lightly doped and very thin, hence, only a few holes (less than 5%) combine with the electrons. The remainder (more than 95%) cross into the collector region to constitute the collector current IC. As a result, almost the entire emitter current flows in the collector circuit. You may note that, current conduction within PNP transistor is by holes. However, in the external connecting wires the current is still by electrons.

Related: Semiconductor Diodes

Bottom Line

The input circuit (emitter-base junction) has low resistance because of forward bias whereas the output circuit (collector-base junction) has high resistance due to reverse bias.

Figure 4: Conventional currents

From our discussion above, the input emitter current almost entirely flows in the collector circuit. Therefore, a transistor transfers the input signal current from a low resistance circuit to a high resistance circuit. This is an important factor responsible for the amplifying capability of the transistor

Don’t miss out on key updates, join our newsletter  List

John Mulindi

John Mulindi is an Industrial Instrumentation and Control Professional with a wide range of experience in electrical and electronics, process measurement, control systems and automation. In free time he spends time reading, taking adventure walks and watching football.

View Comments

Recent Posts

Standard Process Signals for Industrial Instrumentation

Industrial measurement and control processes employ standard process signals that are used throughout all the…

1 week ago

Top 5 Benefits of Combining CCTV Cameras with Biometric Systems

The integration of advanced technologies in security systems has become imperative for ensuring safety and…

1 week ago

Sources of Power Quality Problems

Power quality may be affected by a number of issues. Our discussion in this article…

2 weeks ago

Common Terms Used When Describing Power Quality Problems

Power quality has become an important issue to electricity consumers at all levels of consumption.…

2 weeks ago

What to Expect from PCB Assembly Services in China

The importance of printed circuit board (PCB) technology has escalated throughout the years with the…

2 weeks ago

Magneto-Optic Current Sensors for High Voltage, High Power Transmission Lines

One of the key challenges in measuring the electrical current in high voltage, high power…

3 weeks ago